NSW Old Model Clearvue CV06 Mini

mardi 19 janvier 2016

This is an old model CV06 mini left over from when I was selling them. I have opened it and tried to get it adapted to my workshop vacuum but I decided it was too much trouble as the required hose size is 50mm and mine is much smaller. It is not pristine but it has never been assembled and for those not familiar with this version have a look at this.....

https://www.youtube.com/watch?v=Pmwimab0TeU

These are no longer made in this form and CV have gone to a mini version of their cyclone and this would be the last one available in Oz without any doubt.

Buy it now price is $120 + postage.


NSW Old Model Clearvue CV06 Mini

My first attempt using a quadrant hinge

lundi 18 janvier 2016

Hi all,

I've always admired the look of quadrant hinges, read about them, but was scared by two factors,......the price,...and how on earth do you install them.

So recently I purchased 5 pairs of them. I had a large box in mind to make, wanting to use a nice ring holder that I had left over and designed the box all around it. A rather large box, it doesn't adhere to the "golden ratio" size but I like the result. Getting back to these quadrant hinges. The arms on them were 7.5mm (tad under) wide. The thickness/depth was 1.5mm. I used 11mm timber for the main frame of this box. I would usually use 10mm but went the extra mm for the size of it. So 11 minus 7.5 is 3.5, thus leaving me 1.75mm of timber left on the sides of the box. I routered out the areas using my small plunge router with a 3mm straight bit, and I made a large irregular oval shaped base from 6mm polycarbonate for the router. This enabled me to straddle the base of the router across each side of the box (front and back), to stop it from tilting etc. Reasonably satisfactory, not totally. I then routered freehand.

Getting the depth for the curved piece right is also tricky, but the end result was good. Sits perfectly. Routering freehand was not easy, trying to stay within your area and finish with a chisel. Maybe a template but then I would have to use a flush trim panel bit and the template would be pretty thick as the bearing is in the middle of the bit. Then you might just rip the bit of 1.75mm timber right off and wreck everything. I am thinking next time maybe a 7.5mm brad bit (which I dont have yet), set the guage on the drill press for a neat 1.5mm and clean up with a chisel. Anyway, food for thought.

Here is the result, the box is from Oak and the inserts/tray etc, are from Hornbeam, I am loving that timber now. 315mm x 240mm x 105mm.


My first attempt using a quadrant hinge

A question on tools for making wheels

I'm having a problem finding the right tool to make the wheel on the right. The photo on the left shows how far I have got. The wheel was cut out with a Suttons hole saw and then tidied up on the lathe. I have a few lathe tools but that are too large to cut out the area on the timber to make it look like the photo. The problem arises with the angle the tools need to get to. I have a Woodfast midi lathe and I have given myself as much room as I can using delrin spacers. I have used a parting tool to cut in as much as I can and then swapped to dental pick tools which have a very fine point. They cut nicely into the timber but nothing i have will allow me to square off the hub as shown in the picture of the yellow hub. I was thinking about something like a 1/8" parting tool bend at a right angle to allow the tip to be square to the timber hub. Anyone got any ideas on a tool?

Also, the grooves in the thread in the right hand side pic run 45 degrees opposite to those on the other side of the tyre. There is a deep groove through the centre of the tyre around the circumference. Can you suggest any ideas on inserting these opposing 45 degree tread marks on the tyres.

Any advice appreciated

Greg


IMG_0697.jpgIMG_0700.jpg
Attached Images


A question on tools for making wheels

R.I.P. Glen Frey

R.I.P. Glen B. 5/11/48 - D. 18/01/16
I was never a big Eagles or Glen Frey fan, but you can't deny the incredible talent he had.



R.I.P. Glen Frey

Treadle Metal Lathe and Post drill

Our boys were after a lawn sweeper to go behind the $100 ride on mower we bought last week. We repaired the diff on the mower and got the engine going and now it is a good machine! I checked an add on Gumtree that had just what we were after and also some blacksmith gear. While enquiring about the sweeper I asked about the lathe in the picture and the seller said it was a Treadle Lathe. I couldn't go past it. I have wanted one since I first learnt about lathes!

It needs a good clean and lubrication but it is mostly there with only a few broken pieces and of course no flat belt. I haven't been able to find a makers name anywhere. Any guesses?
The Seller said it came from a Blacksmith shop at Yacka near Clare SA. It has clearly done its share of work.

I also picked up this post drill. It is in very good order.

Pics of coarse!!
Attached Images




Read the full thread at metalworkforums.com...


Treadle Metal Lathe and Post drill

Hi everyone

My name is Vanni from the GC, and I just started playing around with some wood work, I am a novice and started to dismantle pallets for some little projects. I am here to learn more skills and info regarding woodworking. At the moment I am just building some veggie patch raised beds and practice with different type of cuts. I have a circular Saw, a drop saw and on the market to get a table saw.


Hi everyone

Retrofitting Dust Extraction To 14" Woodfast Bandsaw

I am about to start the restoration of my 14" Woodfast Bandsaw.

This will be my first dust generating machine.

The first step is to consider dust extraction since the machine was manufactured without any.

From what I have read, its best to have the dust extraction as close to the point were the dust is created. Also that 150mm ducting is best.

I therefore made this cardboard mockup. It has 150mm hole located on the centre line of the blade and is as close as I can get it.

The dust hood extends beyond the current edge of the sheet metal tool so that it follows / mates with the cast iron frame of the bandsaw, while also centring the 150mm hole on the blade.

I plan to get the dust hood made from sheet metal and then to weld it to the existing sheet metal door.

I plan to have a 90º bend coming off the sheetmetal hood. That will eventually connect to my future dust extraction system.

I am looking for comments and suggestions.

Also will this single point suffice or should I add extra smaller extraction points? I was thinking maybe one on the left edge of the sheet metal door?

Also I have read that supplying enough air for the dust extractor to suck can be a issue. So I was planning to have sheetmetal section directly above the hood removed, basically the small piece that sits on the top next to the white masking tape. Is this good/bad?

I may also consider having ducting coming around the top edge of the sheet metal door and then down the right side of the door terminating just above the blade, to catch any extra dust.

Here are the photos of the mockup.


Attached Images


Retrofitting Dust Extraction To 14" Woodfast Bandsaw
 

Lorem

Ipsum

Dolor